Kexinda Roll Forming Machinery. Co.,Ltd
Call Us
0086 317 8312992
Opening Hours
24hours everyday
Sandwich Panel Production Line Home > Sandwich Panel Production Line
Kexinda Z Lock EPS Sandwich Panel Line From Factory
  • Kexinda Z Lock EPS Sandwich Panel Line From Factory

Kexinda Z Lock EPS Sandwich Panel Line From Factory

Kexinda Z Lock EPS Sandwich Panel Line From Factory
$34000.00
INQUIRY
Kexinda Z Lock EPS Sandwich Panel Line From Factory
 

Features
1. The motor power of the sandwich panel roll forming line is 4kw, and the production speed reaches 6m/min. With the stepless speed regulation system, the efficiency of the roll forming line is optional within 0-6m/min.
2. When producing EPS sandwich panel, the speed is generally controlled at 2-6 m/min. It will be slightly lower for making rock wool board (depends on actual needs)
3. The composite panel production line is equipped with K-9 glue metering pump, featuring low rotating speed and high accuracy. The glue is fed at a rate of 0.1-2.0 kg/min. It is controlled by frequency converter.
4. The thickness of the composite panel the roll forming unit can produce is varied from 50mm to 250mm. By adjusting the upper and lower rack, and the distance between the cutter holder and the material feeding rack, we can get sandwich boards with different thickness and specifications.
5. Total installed capacity: 34KW; total weight (including accessories): 17.5t.
6. Dimension of the panel roll forming machine: 12500 (16000 for rock wool boards) X2200X2800; the roll former for 5 type EPS sandwich panel adopts 23 rubber shafts and 160X80 square tubes with thickness of 6mm; the roll former for 7 type composite rock wool panel employs 45 rubber shafts, and upper and lower independent glue supply. It is equipped with 1.7m rock wool panel conveyor belt, with the diameter of the drive shaft to be 50mm; length of the machine frame is up to 9m; the roll former is welded with 180X80 square tubes which thickness is 8mm.
 
 
 
Requirements for Factories:
The factories where our EPS sandwich panel production line are applied can be either flatroof or sloped-roof type. The height of the cornice should be larger than 5m, and the effective width should be at least 45m. The floor of the factory should be flat and concrete. For foundation of the roll forming line, it is required to be to be 380V, and the total installed power is 34kw. It is necessary for the factory to be equipped with 0.4-0.6MPa compressed air supply and illumination devices. The roll forming machine shares the same power supply with the auxiliary devices. The fluctuation of voltage should be no more than 10%, or it may lead to an abnormal running of the system.
 
The stroke is no less than 29m, the load for a lifting process is larger than 5000kg, and the lifting height is no less than 3.9m. For daily production and maintenance, about 6-10 people are needed, with 3-4 operators for some core processes included.

 

Accessories List of 5 Type Composite Roof And Wall Cladding Panel Machine
adjust spanner 3pieces
filter element 2pieces
big glue head 2pieces
bulkhead glue 4pieces
glue joint 4pieces
steel sheet chuck 2pieces
screw  depends
machine tool pad iron 16sets
brake plate  3 sets
M16×140 bolt 16pieces
axes 1piece
M16 nut 16pieces
steel wire tube 1piece
heating tube 8pieces
heating tube ceramics end  16sets
glue pipe 6pieces
M8×35 inner hexagon screws 30pieces
φ10×80 taper pin 1piece
delivery rack 1set
mainframe 1set
cutting rack 1set
tile plate wheel 1set
overtravel-limit switch 2pieces
pneumatic elements 1 set
glue channel(4long 2short) 6pieces
large tray 1piece
ladder 1piece
M16×40 outer hexagon screws 8pieces
Color clip    4 sets
discharge rack 1piece
05-06 frame 1set
rod 12pieces
00 frame 1piece
hanger 1piece
4 m foam holder 4pieces
long cylinder 1piece
clip lock lever 2pieces
bourdon spring 1piece
1220 roller 8pieces
roller axes 16pieces
6004 bearing  16sets
M20 nut 24pieces
cutting under frame 1 piece
Review


1/3
X